Knife basics

Japanese Knife Steel Explained: VG-10, Aogami, Shirogami, SG2 and More

What the steel names on Japanese knives actually mean, how carbon and stainless steels differ, and which one suits the way you cook.

Published November 16, 2026 · 9 min read

Japanese knife listings are full of steel names: VG-10, Aogami #2, Shirogami #1, SG2, Ginsan. The steel decides how sharp a knife can get, how long it stays sharp, how easy it is to sharpen, and whether it will rust if you leave it wet. This guide explains the common names in plain language.

Carbon steel vs stainless steel

Almost every Japanese knife steel falls into one of two families.

Carbon steel contains very little chromium. It can be made extremely hard and fine-grained, so it takes a very keen edge and is easy to sharpen on whetstones. The downside is that it rusts quickly if left wet, and it reacts with acidic foods, which can discolour the blade and briefly give onions or apples a metallic taste. Over time it develops a grey-blue patina that offers some protection.

Stainless steel contains enough chromium (roughly 13% or more) to resist rust. Modern Japanese stainless steels are very good, but they are generally a little harder to sharpen to the same level as the best carbon steels.

There is also a popular middle ground:

Stainless-clad (san-mai) knives have a hard carbon steel core sandwiched between softer stainless layers. Only the cutting edge is carbon steel, so you get its sharpness while most of the blade surface resists rust. The exposed edge can still rust or discolour, so it still needs wiping dry.

The common carbon steels

Most traditional Japanese carbon steels are made by Proterial (formerly Hitachi Metals) in Yasugi, Shimane, and are named after the colour of the paper they were historically wrapped in.

Shirogami (White paper steel)

  • A very pure carbon steel with few additives.
  • Takes the keenest edge and is the easiest to sharpen.
  • Loses its edge a little faster than Aogami and rusts readily.
  • Grades: #1 has more carbon (harder, more brittle), #2 is slightly tougher and more forgiving, #3 is softer and less common in good knives.

Aogami (Blue paper steel)

  • Shirogami with chromium and tungsten added.
  • Holds an edge longer and is a bit tougher, but is slightly harder to sharpen.
  • Aogami #2 is one of the most common steels in handmade Japanese knives.
  • Aogami Super has more carbon and additional alloying for even longer edge retention, at the cost of more care and harder sharpening.

The common stainless steels

VG-10

  • Made by Takefu Special Steel in Fukui.
  • Stainless steel with carbon, chromium, cobalt and vanadium. Usually hardened to around HRC 60–61.
  • The most widely used Japanese stainless steel. Good sharpness, decent edge retention, low maintenance.
  • Often used as the core of layered “Damascus” pattern knives.
  • A sensible default for a first Japanese knife.

SG2 / R2

  • Powdered (powder-metallurgy) high-speed stainless steel. SG2 is Takefu’s name for it; R2 is the equivalent from Kobelco.
  • Can be hardened to around HRC 62–64 and holds an edge for a very long time.
  • More expensive, slower to sharpen, and the thin hard edge can chip if misused.
  • Good for experienced cooks who hate sharpening often.

Ginsan (Silver #3)

  • A Proterial stainless steel often described as the stainless steel that feels most like carbon steel on the stone.
  • Fine-grained, easy to sharpen, rust-resistant. Popular in traditional single-bevel knives made for overseas buyers who want low maintenance.

AUS-8 and AUS-10

  • Stainless steels from Aichi Steel.
  • AUS-8 is softer and tougher, common in entry-level knives. AUS-10 is closer to VG-10.
  • Easy to live with; AUS-8 needs sharpening more often.

Other names you may see

  • HAP40, ZDP-189, SRS-13: high-end powder steels with very long edge retention, favoured by enthusiasts.
  • Molybdenum (Mo) steel / “Molybdenum vanadium”: usually a general term for softer, budget stainless steels used in many everyday Japanese home knives.

What “HRC” means

HRC is the Rockwell C hardness scale. Typical European kitchen knives sit around HRC 55–58. Many Japanese knives are HRC 60–64.

  • Higher hardness: thinner, sharper edge that lasts longer, but more brittle. Twisting the blade in hard food, cutting frozen food or hitting bone can chip it.
  • Lower hardness: the edge rolls rather than chips and is quicker to touch up, but dulls sooner.

A harder knife is not automatically better. It is better for careful slicing and worse for rough use.

Which steel should you choose?

Your situation Good choice
First Japanese knife, want low maintenance VG-10, AUS-10 or Ginsan
Want the sharpest possible edge and enjoy sharpening Shirogami #1 or #2
Want carbon-steel performance with a bit less sharpening Aogami #2 (stainless-clad if possible)
Rarely want to sharpen, cut carefully SG2 / R2
Shared household kitchen, knife may be left wet Stainless only

Basic care for any Japanese knife

  1. Hand wash and dry immediately. Never use a dishwasher.
  2. Use a wood or soft plastic board.
  3. Don’t twist or pry with the blade; don’t cut bones or frozen food.
  4. Store it in a block, on a magnetic strip, or in a blade guard, not loose in a drawer.
  5. For carbon steel, wipe the blade during use when cutting acidic food, and put a thin coat of food-safe oil on it if it will be stored for a while.
  6. Sharpen on whetstones. Pull-through sharpeners can damage hard, thin Japanese edges.

Next: Gyuto vs Santoku vs Nakiri: which shape to buy first.